![]() ![]() This drive is mounted using /etc/fstab: UUID="1655887b-96c2-40dd-80e2-87e2fdce83c6" /media/USB12 ext4 defaults 0 0Īnd then it is shared through samba nano /etc/samba/smb. I have also (with it unmounted) issued chmod 666 /mnt/test as I found reports that resolved the issue. UUID : d0b5192e:3b2b1fd7:f43639bb:e041cac6 I have successfully mounted a samba share (from a Centos server) on my Raspberry Pi, but the share is read-only: sudo mount -t cifs //ip.address/sharename /mnt/test -o userusername,vers1.0. I have used mdadm to create a simple 'RAID1' array: sudo mdadm -detail /dev/md0 I have a raspberry pi 4 with two USB drives attached. Or is this a docker issue and do I have to do something about the file permissions inside the docker container (there is a folder on the NAS drive that's mapped as a volume in the docker container) Setup on raspberry pi 4 the NAS deviceįor completeness, here is how the NAS device is set up: 'Please change the permissions to 0770 so that the directory cannot beĬan I change the file permissions consistently? This is an issue when I try to set up a NextCloud docker container, as the NextCloud webapp tells me during installation: When I try to change the permissions with sudo chmod -R 0770 /media/PiNAS the file permissions are not changed. Please make sure that the credential file using LINUX (LF - ) instead of WINDOWS (CRLF - \r ). I assume that the username and password were correct. ![]() PiNAS/PiNASdrive /media/PiNAS cifs vers=3.0,credentials=/home/USERNAME/.secrets/.smbdPiNAScredentials,nodev,nosuid,uid=1000,gid=1000 0 0 at 22:37 this error most likely connects to NTSTATUSLOGONFAILURE which you can see them in dmesg. The NAS drive is mounted using cifs and /etc/fstab: sudo nano /etc/fstab: (Check that by issuing the id command when logged in as pi.I am struggling with file permissions on a mounted NAS on my ubuntu server ( 20.04 LTS). Note that this assumes that the pi user is user 1000. For example: /dev/sda2 /home/pi/HDD ntfs-3g defaults,user,uid=1000,gid=1000,noatime 0 0 If you're going to add this mount to your /etc/fstab file and still want it mounted by the pi user, then you'll need to specify the uid and gid on the line. As already mentioned in the answer you got, the FAT file system doesn't support such permissions, so they can't be applied after the drive is mounted. If you created the /home/pi/HDD directory while logged in as the pi user, and before mounting the external drive, that's already done, so you can simply skip that step. The point at which you are apparently stuck is the chown command, but all that is intended to accomplish is to make sure that "you" (really the pi user) actually owns the folder to be shared. It seems to me that the real issue is that the instructions, as written, don't work generically. You are probably not doing anything wrong. Serverfault is not the place for this question, so asking it here instead. Ask on Serverfault if you still have a problem. vfat doesn't support ownership and groups, hence the operation not permitted. Voted to close as off-topic for StackOverflow. Posted this on stackoverflow first by mistake, and got this answer: I ran the diagnostics from my PC and I can find. Providing the credentials of the user pi I get the message The user name or password is incorrect. However, providing the credentials of my new user I get the same Access Denied message. Typing mount in the terminal after this gives the same output as before. When I try to create a mapping from my PC to the Pi, I get Access Denied no matter what user I use, even pi. where SHARENAME is the section name in smb.conf, I can browse and see all the shares. Googled a bit and found this post, so I tried this without any error messages: $ mount -o remount,gid=1000,uid=1000 /home/pi/HDD It may be that the security is root:root (esp if mounted via fstab) boolian2. You need to check the permissions on the share mount location. ![]() (rw,noatime,fmask=0022,dmask=0022,codepage=437,iocharset=ascii, Re: Transmission permission denied to mounted SMB folder. If I type mount in the terminal, the output regarding the external harddrive is: /dev/sda2 on /home/pi/HDD type vfat I have also tried it as superuser ( sudo su), but with the same error. "Make sure your user is the owner of the path you are trying to share via Samba sudo chown -R pi:pi /path/to/share" I am following this tutorial to create Samba Share on my Raspberry Pi Zero.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |